|
The InFlow
W125 ducting kit enables any IQAir® filtration system to draw air through
a wall or window vent into an indoor environment. Use of the InFlow W125
is advisable when the main pollution source is located in adjacent
indoor environments or outdoors.
Enjoy
controlled clean air ventilation
An IQAir® filter system combined with an InFlow W125 can be installed to
draw outdoor air into an indoor environment. In this setup, an IQAir®
serves as a ventilation system, bringing in oxygen-rich outdoor air and
a filtration system, which removes undesirable outdoor pollutants such
as pollen, mold spores, dust and exhaust soot. As a result, fresh and
filtered outside air comes into the room.
Create clean positive pressure areas
An IQAir® filter system combined with an InFlow W125, which draws air
into a room will in most cases allow the creation of a positive
pressure. This positive pressure helps to clean the air in a room by
constantly flushing out air pollutants and by preventing outside
pollutants from entering the room.
Application Examples
-
protection of
allergy sufferers from pollen exposure in their home
-
protection
of patients from microbiological exposure (e.g. aspergillus) in a
hospital
-
creation
of clean research or manufacturing areas (controlled environments)
-
protection
of plant control rooms from corrosive contaminants
-
creation
of a clean zone within a home or office which helps to prevent outdoor
pollution from nature, factories, traffic, agriculture to enter.
Using an
InFlow W125 with an IQAir® system can improve indoor air quality by:
-
diluting polluted air with clean air
-
flushing out air pollutants
-
reducing influx of new outside pollutants due to a build-up of
positive pressure
-
by increasing oxygen content in indoor air (when outdoor air is
being drawn in)
Installation
The InFlow W125 kit can be easily added to any IQAir® filtration unit in
a matter of minutes. As regards the building, the only modification
required is a 5” hole in a window, wall or door which allows to connect
the InFlow W125 aluminum duct.
The duct may be freely flexed to allow control over the desired vent
location. It is expandable in length, from 10” in its original
compressed state, to 39” when fully extended.
IQAir®
Compatibility
Compatible with all IQAir® filtration devices.
Not compatible with the accessories PF40, VMF, VM FlexVac, VM InFlow and
FlexVac. |
|
The
OutFlow W125 kit allows filtered air from any IQAir® filtration device
to be directed through a wall or window vent. The OutFlow W125 kit can
be used to:
-
create clean areas
-
deliver filtered air into cleanrooms or to the
outside
-
create negative pressure areas
-
create positive pressure areas
Clean
Area and Cleanroom Use
The supply of filtered air into an environment helps reduce air
pollution in that environment by dilution and the creation of positive
pressure, which reduces the infiltration of polluted air from outside
the environment. With the OutFlow W125 kit, the filtration device is
positioned outside the clean area or cleanroom, saving valuable space
and reducing noise exposure. It also eliminates the danger of housing
leakage, making it suitable even for certified cleanrooms.
Emission Control
Legislation limits the emission of polluted air to the outdoors. The
OutFlow W125 filters air before it is exhausted outdoors to help meet
environmental emission standards.
Isolation Areas
Infection control (e.g. tuberculosis) in hospitals and similar
facilities demands the creation of negative pressure environments to
reduce the spread of airborne microorganisms. The OutFlow W125 permits
operation of the filter unit from within the isolation area, eliminating
the danger of housing leakage into the surrounding area.
The OutFlow W125 kit easily modifies any IQAir filtration unit. Simply
replace the top module of any standard IQAir® filtration unit with the
TopFlow adapter. All that is needed to install the ducting, wall tube
and vent is a 5.2" opening in a wall or window. The OutFlow W125 kit
also includes a damper and a protective mesh grille which prevents
backdrafts and entry of coarse particles when the system is not in use.
The large 5" diameter of the ducting ensures low air resistance.
The aluminum duct may be freely flexed to allow control over the desired
vent location. It is expandable in length from 10" in its original
compressed state to 39" when fully extended. |
IQAir
IQAir
